Buy MICROCHIP AT89CPU online at Newark element Buy your Technical Datasheet: AT89CPU Datasheet. See all Technical Docs. Microchip AT89CPU: available from 31 distributors. Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing. AT89C, AT89CPU, AT89C Pin 24MHz 2kb 8-bit Microcontroller, buy AT89CPU. AT89CPU – AT89C Pin 24MHz 2kb 8-bit Microcontroller Technical Data – Buy AT89CPU Data Sheet.

Author: Kazigis Arashira
Country: Swaziland
Language: English (Spanish)
Genre: Medical
Published (Last): 27 December 2008
Pages: 62
PDF File Size: 4.95 Mb
ePub File Size: 16.63 Mb
ISBN: 879-5-57763-498-8
Downloads: 6245
Price: Free* [*Free Regsitration Required]
Uploader: Kigasho

It is completely independent, but it 24pi developed as its component Current nibble high or low is determined by the state of the 6Q bit pin 14 of the system latch It still works since Atmels sustain a lot; however, their opinion is included here simply because xt89c2051 are right. Several people have independently pointed out that the voltage switches are not designed in a totally “clean” way. Instead of waiting 1. It connects directly to a PC parallel port.

The original design used the circuit; however, its use did not prove to be useful due to the parallel port output design see the article about LPT. Features of the AT89C processor: Data protection system is designed very well. We tried to minimize this influence in our design; however, there is no way to remove these side effects completely with respect to simplicity. Software is written datashete Pascal, the new version uses the Turbo Vision user interface.

LEDs are used to decrease voltage and to indicate current process. The lowest power consumption can be achieved with clock frequency of 2 MHz, and amounts to about 6 mA for the processor itself add 2mA for a miniature The only disadvantage of this processor is a small and non-expandable program memory.


Both software versions support so-called DEBUG mode, that should greatly simplify any troubleshooting.

AT89CPU – AT89C Pin 24MHz 2kb 8-bit Microcontroller Technical Data

A simple programmer for the Atmel AT89c microcontrollers. We are working on a reprint.

We paid great attention to the timing routines, so it should work on any computer. Big thanks to the author. If you need more exact specifications, download the original datasheet in. You can view the modified qt89c2051 here.

Atmel AT89C2051 programmer

The circuit is intended for simple applications, where room and number of wires are limited. Programming modes Pulse widths Timing diagram for programming and verification Practical part: Its output is accessible ratasheet the software via the P3. Or, “in an emergency”, you can use two standard cheap sockets inserted into each other, so the soldered one is not subject to excessive mechanical stress.

April – Increment address counter by pulsing XTAL1, set next instruction code via P1 Repeat steps 5 to 8 until the 2kB boundary is reached, or until the whole file has been programmed into the chip.

For example, resident printing programs can do almost anything with the LPT. In some cases, it’s better to use a ta89c2051 design for the voltage switching part – see the end of this article.

With the AT89C51, it is not even possible to transfer contents of the internal FLASH memory if an external memory with a special datasheey is attached to it.


The only major inovation over standard series processors is the analog comparator on pins P1. In the first case, it’s not recommended to use the stabilisers; when an input voltage is connected to their outputs, they consume about 50 mA and convert it to heat.

It is definitely better to use two 8-bit “D” flip-flopswhich are triggered by edge, not by level.

My objective was to build a simple programmer, that would be easy to make at home and would work without significant problems on the first try.

Set the programming mode via pins P3. There is no further significant power consumption drop at lower clock frequencies. It should work with no problem on the first try. It was designed using common components, with datasueet to simple construction.

Optionally, set verification mode via bits P3. Data reading and verification is controlled by circuit – four multiplexers, allowing to read 8 bits via four parallel port input bits.

It’s a pity it can’t run just with a RC-circuit for clock signal generating, and that an OTP version is not available. According to our measurements, power consumption averages approximately 12 mA.

Due to undefined state of the LPT port after running some applications, it datasheft necessary to turn on the power for the programmer AFTER starting the control software.