E/ECE/ E/ECE/TRANS/ } Rev.1/Add/Rev Regulation No. 48 page 3. Regulation No. UNIFORM PROVISIONS CONCERNING. Regulation No 48 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. Regulation No 48 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of.
|Published (Last):||24 October 2016|
|PDF File Size:||12.36 Mb|
|ePub File Size:||7.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
The above approval mark affixed to a vehicle shows that the vehicle type concerned has, with regard to the installation of lighting and light-signalling devices, been approved in the Netherlands E4 pursuant to Regulation No 48 as amended by the 05 series of amendments.
Rear side-marker lamps shall be amber if they flash with the rear direction-indicator lamp. And for a trailer, when the trailer is connected to a drawing motor vehicle in the conditions as prescribed in Paragraph 2. For the purpose of this Paragraph, “vehicles” means vehicles of Categories L, M, N, O, T, as well as bicycles, such vehicles being equipped with retro-reflectors, with lighting and light-signalling devices, which are switched ON.
Although all countries’ type approvals are legally equivalent, there are real and perceived differences in the rigour with which the regulations and protocols are applied by different national type approval authorities.
EUR-Lex – X(03) – EN – EUR-Lex
For S3 or S4 Category devices: The rear fog lamp s can be switched off independently of any other lamp; 6. Presence Devices of S1 or S2 categories: Languages, formats and link to OJ. Two optional lamps category 2a or 2b on all vehicles in categories M 2M 3N 2N 3.
Reversing lamp Regulation No 23 6. Above the ground, not less than mm nor more than mm not more than 1,mm if grouped with any rear lamp s1,mm if the shape of the bodywork makes it impossible to keep within mm or 1,mm respectively. For motor vehicles, the length of the vehicle excluding the cab, or in the case of tractors for semi-trailers, if fitted, the length of the cab. A light source module is so designed that regardless the use of tool sit is not mechanically interchangeable ecs any replaceable approved light source.
Regulation 49 – 06 series (click to expand)
This requirement shall not apply, however, to main-beam or dipped-beam headlamps when their luminous warnings consist of the intermittent lighting up at short intervals of the main-beam headlamp or the intermittent lighting up at short intervals of the dipped-beam headlamp or the alternate lighting up at short intervals of the main-beam and dipped-beam headlamps. The maximum height above the ground shall be measured from the highest point and the minimum height from the lowest point of the apparent surface in the direction of the reference axis.
Position No special requirements.
If there is a danger of dazzling other road users by the movement of the lamps, they may light up only when they have reached their position of use. The exterior courtesy lamps shall not be activated unless the vehicle is stationary and one or more of the following conditions is satisfied: The outer edge of the apparent surface of at least one lighting unit on each side of the vehicle shall not be more than mm from the extreme outer edge of the vehicle A in the figure ; and, The inner edges of the apparent surfaces in the e48 of the reference axes shall be not less than mm apart.
The competent authority issuing the extension of approval shall assign a series number for such an extension and inform thereof the other Parties to the Agreement applying this Regulation exe means of a communication form conforming to the model in Annex 1 to this Regulation.
Two of the lamps visible from the rear may be grouped, combined or reciprocally incorporated in accordance with paragraph r4. Tell-tale Closed-circuit tell-tale optional, however a tell-tale indicating failure is mandatory if required by the component regulation.
If the holder of the approval completely ceases to manufacture a type of vehicle approved in accordance with this Regulation, he shall inform the authority which granted the approval. Number Two or four, type ecr according to Regulation Nos ecce, 98, orexcluding Class A headlamp.
The illuminating surface of the retro-reflector may have parts in common with the apparent surface of any other lamp situated at the front. For a motor vehicle, when the vehicle is ready to move with its propulsion engine running and its movable components in the normal position s as defined in paragraph 2.
Two S1 or S2 category devices and one S3 or S4 category device on all categories of vehicles. Retrieved 20 March The application for the vehicle type-approval shall, in this case, contain information as to which of the two alternatives is to be used.
This information shall remain displayed as long as the adaptation is activated. Electrical Connections In accordance with Paragraph 5. The changes within and between the provided classes and their modes of the AFS lighting functions as specified below, shall be performed automatically and such that no discomfort, neither for the driver nor for other road users, is caused. Any temporary fail-safe replacement of the light-signalling function of a rear position lamp is allowed, provided that the replacement function in case of a failure is similar in colour, main intensity and position to the function that has ceased to operate and provided that the replacement device remains operational in its original safety function.
Drawing vehicles for semi-trailers: The aggregate maximum intensity of the main beam headlamps shall be checked by the procedure described in paragraph 6. The approval mark shall be clearly legible and be indelible.
InterRegs: Regulation No. | ECE – United Nations
Reason s for extension if applicable: When the reversing lamp is switched ON, both cornering lamps may be switched on simultaneously, independently from the steering wheel or direction-indicator position. The distance between the inner edges of the two apparent surfaces in the direction of the reference axes shall not be less than mm.
As from the official date of entry into force of the 04 series of amendments, no Contracting Party applying this Regulation shall refuse to grant approval under this Regulation as amended by the 04 series of amendments.